标准规范下载简介
ISO 15614-1-2017-（中英文对照）金属材料焊接工艺规范和鉴定-焊接工艺试验 第1部分.pdf简介：
ISO 15614-1:2017，中文名为《金属材料焊接工艺规范和鉴定-焊接工艺试验 第1部分：简介》，这是一个国际标准，由国际标准化组织（ISO）发布。该标准主要关注焊接工艺的规范制定和验证，目的是为了确保金属材料焊接的质量和一致性。
该标准的目的是为焊接工艺的实施提供指导，包括焊接材料的选择、焊接方法的确定、焊接参数的控制、焊接试验的进行以及焊接结果的评估。它适用于各种类型的金属材料，包括结构钢、不锈钢、铝合金等，以及各种焊接方法，如电弧焊、激光焊、电阻焊等。
该标准的1部分主要涵盖了焊接工艺的基本概念、术语和符号，焊接试验的目的和类型，以及焊接工艺规范的制定原则。它为焊接工程师、技术人员和质检人员提供了一个通用的框架，以确保焊接过程的标准化和质量管理。
由于标准涉及到专业术语和技术细节，建议在使用时参考英文原文或由专业机构提供的中文翻译。
ISO 15614-1-2017-（中英文对照）金属材料焊接工艺规范和鉴定-焊接工艺试验 第1部分.pdf部分内容预览：
Table 5 ( continued )
Table 6 Range of qualification for nickel alloy and nickel alloy/steel groups 镍合金和镍合金/钢组的认可范围
Table 6 Range of qualification for nickel alloy and nickel alloy/steel groups 镍合金和镍合金/钢组的认可范围
3.3.2Materialthickness母材厚度
fortestpieces 16mmthickorgreater,theminimumthickness qualified is16mm;对于16mm厚或更大的测试 件DB14／T 2244-2020 危险化学品重大危险源管理信息化业务流程规范.pdf，合格的最小厚度为16mm for test pieces less than 16 mm thick, the minimum thickness qualified is the thickness of the test piece; 对于小于 16mm厚的试件，合格的最小厚度是试件的厚度 for test piece thicknesses 6 mm and thinner, the minimum thickness qualified is O,5 times the thickness of the test piece.对于6毫米厚的试件厚度，最小厚度为试件厚度的0.5倍。
Table 7 Range of qualification for butt welds material thickness and deposited metal thickness对接焊缝材料厚度和焊缝熔敷厚度的认可范围
Dimensions in millimetres
Table 8—Forlevel2:Rangeof qualification thickness and throat thickness of filletwelds第2级：角焊缝材料厚度和喉部厚度限定范围
imensionsinmilimetres
8.3.3Diameterofpipesandbranchconnections管子和支接管直径的认可范围
3.3Diameterofpipesandbranchconnections官 For level 1: The diameter is not an essential variable. Any product form, i.e. plate, pipe, forging or casting. qualifies for all product forms
For level 1: The diameter is not an essential variable. Any product form, i.e. plate, pipe, forging or casting. qualifies for all product forms
For level 2: The qualification of a welding procedure test on diameter D shall include qualification for diameters in the following ranges given in. Table 9. A butt weld qualification for pipes covers butt welds in plates. Qualification given for plates also covers pipes when the outside diameter is >500 mm or when the outside diameter is >150 mm welded in the PC, in PF rotated position or in PArotated position.当管子外径 大于500mm，或者在PA或PC转动位置上的管子 外径大于150mm时，板材的评定适用于管子
For level 2: The qualification of a welding procedure test on diameter D shall include qualification for diameters in the following ranges given in. Table 9 A butt weld qualification for pipes covers butt welds ir plates. Qualification given for plates also covers pipes when the outside diameter is >500 mm or when the outside diameter is >150 mm welded in the PC, in PF rotated positionor inPArotated position.当管子外径 大于500mm，或者在PA或PC转动位置上的管子 外径大于150mm时，板材的评定适用于管子
labley F'orlevel connection diameter 管子和支接管的认可范围
vel 2: Range of qualif 管子和支接管的认可范围
Dimensions inmilimetre
Angleofbranchconnection支接管的角度 For level 1: The angle of branch connection is not an essential variable.
For level 2: A welding procedure test shall be car. ried out on a branch connection with angle α (see Figure 4). A test piece made with a branch angle (α) between 60°and 90° in the procedure test qualifies the angle 60°≤α <90°. An angle α < 60° requires a separate test piece and qualifies angles from α up to 90° 在过程试验中，以分支角（α）为60°一90°的试验 片，使60≤α<90°的角度。角度α<60°需要单独的 测试件，并且可以将α至90°的角度进行限定
JGJ／T 220-2010 抹灰砂浆技术规程(完整正版、清晰无水印).pdfa) the variables associated with each process and consumable are addressed in the pWPS; b) the parent material and deposited metal thickness limits of
For level 2: When the test piece is welded with more than one welding process, the procedure is valid only for the sequence of processes used on, provided the test piece. Test specimens shall include deposited material from each welding process used
Back run is permitted using one of the welding processes used in the qualification.
Table 7 for each process and consumable are restrictec in the p WPS to the thickness limits qualified.
8.4.2Weldingpositions焊接位置
8.4.4Fillermaterial.manufacturer/tradename.designation填料，制造商/商品名称
8.4.4Fillermaterial.manufacturer/tradename.designation填料，制造商/商品
DL／T 1817-2018 变压器低压侧用绝缘铜管母使用技术条件8.4.5Fillermaterial size填料尺寸